Johnson Granite Supply Anchor Stencil

Johnson Granite Supply

"Preserving Memories"

ANCHOR STENCIL

#111 Stencil a low-tack stencil designed specifically for easy hand cutting, which means less wear and tear on instruments. Panels can be easily and accurately replaced. White release liner is easily removed. Available in 12 3/4", 14 1/2", 18 3/4", 25" and 30" widths.

#112 Stencil a low-tack convertible stencil designed for machine or hand cutting without having to reverse the liner. Controlled release capable due to extra-heavy red liner. Available in 12 3/4" and 25" widths.

#116 Stencil a high-tack, single back, computer stencil formulated to adhere to brick, raw wood surfaces and urethane foam board without using filler. Features trimmed edges and a clear, strong film liner that offers easy alignment and smooth, precise running on computerized sign-making machines. NOTE: this stencil has a very aggressive adhesive system and is not recommended for use on soft woods without first testing a sample piece. Available in 15" and 30" widths.

#117 Stencil a medium-tack version of #116 designed for use with computerized cutting machines, specifically made for use on pretreated and pre-painted surfaces. Can be used safely on glass, tile, sign foam and synthetic stone. A strong, clear film provides extra rigidity. Available in 15" and 30" widths.

#120 Stencil a multipurpose, medium tack, dark blue liner stencil designed for shape and depth carving in glass, pretreated and pre-painted soft woods ,tile, pretreated foam board or Plexiglass. This stencil is very easy to had-cut. Fillers not normally required which simplifies application and cleanup. Available in 20" width.

#123 Stencil is designed for machine or hand cutting. Has a 1mm clear polyester liner between outside blue liner and rubber stencil which eliminates taping during the panel transfer to stone, yet allows easy blast-through. Available in 12 3/4", 14 1/2", 15", 18 3/4", 21", 25" and 30" widths. Also available with YELLOW liner.

#124 Stencil is same style as #123 with a blue liner. The computer holes are punched through the liner and rubber. Available in 15" width x 10 yard length and 30" width in both 10 and 20 yard lengths. Also available with YELLOW liner.

#125 Stencil is a high-tack stencil designed for sandblasting raw wood and urethane foam board. Has an easy-release orange liner. The strength of the adhesive eliminates the need for filler or adhesives, saving you time and money. NOTE: do not use on pre-painted sign or glass. Available in 25" width.

#128 Stencil is an 18mm hand cut stencil designed for glass etching, light stone, tile and acrylic etching. The paper liner is easily removable. This stencil conforms nicely to irregular and curved surfaces and has a great blast resistance and leaves no residue when pulled off. Available in 25" and 30" widths.

#129 Stencil is designed for use on most computer cutters, this product has a clear, 3mm polyester outer film liner. A sheet of 1mm middle liner polyester film between the outside liner and rubber stencil holds the centers in place while transferring stencil from computer to granite. Available in 15", 25" and 30" widths YELLOW only.

#153 Stencil is designed for use on friction-feed cutter, which means that two wheels clamp down on the stencil and pull it through the computer while cutting letters and designs. This type of computer has no sprockets, so holes are not needed. Stencil can be used on pretreated and pre-painted wood, tile, acrylics and urethane foam board. No filler required, saving you time and money. Available in 19 7/8" and 24" widths.

#154 Stencil is the same construction as the #124 computer stencil. Holes are IBM configuration (1/2" spacing) and should be compatible with any computerized cutting machine with matching sprockets. Available in 12 3/4", 14 1/2", 15", 18 3/4", 25" and 30" widths. The 25" and 30" are available in 10 or 20 yard lengths. Also available in YELLOW liner.

#155 Stencil is the same design as the #153, except this stencil's adhesive is water-based rather than petroleum based, making adhesion much higher. The rubber is trimmed back 1/2" along each edge so the wheels can clamp down on the 5mm polyester film liner and carry the stencil through the computer. Recommended for sandblasting brick and unfinished wood. Available in 19 7/8" and 24" widths.

#156 Stencil is the same as style #116, except the hold pattern is for a 1/2" spaced sprockets computer cutter. NOTE: this stencil has a very aggressive adhesive system and is not for use on soft woods, pre-painted, pretreated or glass surfaces. Available in 30" width.

#157 Stencil has the same construction as #117, except the hole pattern is for a 1/2" spaced sprockets computer cutter (same as #156). Available in 30" width only.

#158 Stencil has the same construction as #117, except the hole pattern is for a 1/2" spaced sprockets computer cutter (same as #156). Available in 25" width only.

#211 Filler is specifically designed and formulated to produce superior results with Intertape stencils. Formulated for use on polished, frosted or axed surfaces. Use with stencil styles #111, #112, #117 and #157.

#223 Filler is specifically designed and formulated to produce superior results with Intertape stencils. Can be used on polished, frosted or axed surfaces. Use with stencil styles #123, #124, #129 and #154.

#333 Filler is a versatile filler that is water washable, which minimizes fumes, fire hazards and waste spills. Best of all, this product lasts twice as long. This filler is compatible with all Intertape stencils.

A technology leader, IPG is committed to providing superior products that offer:

Superior Blast Reistance ~ Perfect designs ~ Easier Cutting~ Cleaner transfer of artwork to stencil and easy release liners ~ Smooth and accurate tracking ~ Variety of sizes

Information from www.intertapepolymer.com/stencil.html